Jump to content

Leaderboard

Popular Content

Showing content with the highest reputation on 07/21/2019 in all areas

  1. ended going with uShip. Cost me more but I’m getting it when I wanted it (now!). Bike is currently going through Paducah, Kentucky. ETA is Wednesday. Shipping was $750 plus $50 uShip fee ($800 total). Transporter pays $150 to uShip. Next time I can go direct with transporter and save $200.
    4 points
  2. 3 points
  3. I'd say this is not acceptable, even when it's quite common. Make sure you use 12.9 bolts and torque them to 40Nm. You may also cut the slots some millimeters deeper to ease the clamping. Of course, that's up to what nerves you have in real life, internet off. But done properly it's a proofen modification. Some words about the alignment: Because of the wide rear tyre the U-Joints don't move in one plane only. Look from above and you'll see the shaft pointing outwards. That's the reason they weld them with some degrees more/less then 180°, it's to reduce the resulting transmission failure. And be easy with grease on the moving part of the shaft. The spines should be able to glide 'freely', too much grease and they're stuck. Common fault because this zerk is the only one everyone can reach
    2 points
  4. Thank you sir. It’s how it should have come from the factory, given the nature of a tribute to the great Omobono Tenni. Prevented by bean counters in favor of market and model line pricing. Tenni Corsa ... f - ‘em, I’ll do it myself.
    2 points
  5. The temperature sensors are usually NTC thermistors mounted in a housing. NTC (negative temperature coefficient) means that as the thermistor temperature rises, it's electrical resistance drops. The measurements you made need to account for temperature of the sensor, for example is it in your warm hand or outside in the cold. If you are talking about the air sensor in the air box, it is usually trouble free, unless your friend is in the "pod filter" brigade. Then he needs to mount the air sensor somewhere where it measures only intake air. https://www.v11lemans.com/forums/index.php?/topic/19831-air-temp-mod-for-no-air-box/ Since a thermistor circuit is usually low current to avoid self heating, the circuit is sensitive to extra resistance from a bad connection. Unplugging and replugging connectors can help, especially if you clean and treat the connectors with something like DC4 or DeoxIT. I bought packs of 20 thermistors from Aliexpress for about $2 a pack. Let me know if you want a selection sent to you, I know I will never use them all. Note that the rating for thermistors is measured at 25 degC. The illustration below is for the V11 air intake sensor, but the V11 oil temp sensor has the same rating thermistor in a different housing.
    2 points
  6. Pic from another period. Ancient English industry
    1 point
  7. Very short ride, 98 degrees and high humidity captured my attention. Just making sure it all works. As one would expect, a solid reassuring grip and bounce. A better longer ride is yet to come. The true test, on southern Indiana roads.
    1 point
  8. WOWOWOWOWOWOWWWWWW!!!!!! This is one extraordinary Tenni! Welldone, footgoose!!
    1 point
  9. Having used both the OEM plastic and the all-brass "upgrade", I can say my 2000 Sport runs better with the plastic one. Theory is, that the brass retains heat too long and makes the ECU adjustments lag slightly behind actual conditions, leading to poor running.
    1 point
  10. Marty: PERFECT, thanks. Here is an interesting article from Murray (Down under) posted May 22, 2007 After just playing with one to find out its not the problem The "engine oil temp sensor" which is acutally the head temp sensor and has little to !@#$ all to do with the oil temp. What makes me say that I have a bike that has an additional temp sensor in the oil cooler and the reading out of that are radically different to the head temp sensor. Is a NTC (negative temperture coefficent) themocouple with a range of -40 to 170 ish degrees celcius. NTC means as the temp goes up the resitance goes down resitance at 10 degrees is around 3.7K ohm and at 80 degrees is 0.37kohm. Buy rights you should be able to bung a 10cent resitor in there and run home on that if it fails. The sensor does not earth through the cases oil preasure switch style but has a return line to the ECU. Hope this helps NB all temps are celcius/metric.
    1 point
  11. Stay easy, folks! It's the internet only.
    1 point
×
×
  • Create New...