Jump to content
docc

Wheels Off Maintenance Checklist

Recommended Posts

Here's a list of things to inspect, clean or lubricate while the wheels are off for a tire change:

(The wheels don't have to be off to do all of these maintenance points, and not all need to be done every time)




>Check the wheel bearings for smoothness and play.

>Clean and check the brake pads for wear; polish and grease the pin(s) very lightly with a silicone based grease..

>Clean the brake pistons and restore their motion in and out of the calipers evenly. This involves blocking every piston but one and moving it in an out of the caliper all the while cleaning it with brake cleaner.

 

> This good advice from gstallons on brake drag: http://www.v11lemans.com/forums/index.php?showtopic=20133&p=225343

>Bleed brakes, especially the rear brake while you can turn the bleeder to the top.

 

>Remove the top and bottom rubber caps from the rear brake master cylinder and inspect, clean, and lubricate. Use only silicone based grease around brake parts (under the master cylinder, inside the rubber cap). Make sure there is good electrical connection to the switch at the top and avoid the silicone based lubes (dielectric) on electrics - simple petroleum jelly (Vaseline®, or better: Caig DeOxit Gold®) will keep the moisture out. Grease does not conduct electricity - it's just to keep the moisture out. http://www.v11lemans.com/forums/index.php?showtopic=18158&p=192643

>Clean the rear brake carrier pin and block; lube lightly and be certain the pin threads are clean, lubed* and well torqued. (later V11s have a retaining clip on the inboard side). *Consider a thread locking compound.
Allowing this locator pin to fall out can be catastrophic! On the early V11 (1999-2002), some have decided to torque the pin in place and only use the sliding block to remove the rear wheel, perhaps reducing the chance that the pin would not be reinstalled correctly and safely.

>Bleed the clutch.

>Clean the gearbox vent and the rear drive vent.

 

>Inspect the rear exhaust crossover hanger and both of the canister/passenger peg subframe supports.

>Clean the wheels and rotor carriers ("float buttons") and lube the front carrier buttons (a drop of Breakfree CLP (or equivalent) works well, but don't let it sling out on the rotor surface. Bumping the rotors around with a mallet helps keep them “floating.” Even out the spacing of the rotor on the carrier  by tapping evenly around the perimeter of the rotor with a soft mallet.

>Check the  torque reaction rod (chassis rod) rubber bushings for deterioration and play.

>Check the rear drive bearings; clean and grease the outboard needle cage and its sleeve with a good waterproof grease insuring that you rotate it to a new position. Here is an excellent thread, by Bjorn, with lots of great pictures of this bearing, the swingarm, and the bevel box internals. [edit 26 April 2018: It has come to light that keeping moisture out of the right side needle bearing protects the "nose" of the crown wheel and the inner drive seal. Once pitted, the crown wheel is difficult to restore.)

>Clean and grease the drive splines for the hub. Use something super-sticky, like Klüber Staburags or a dry-film moly coat. Avoid over-greasing (it will just sling off).

>Lube the driveshaft and its U-joints. Don't put too much grease in the splined connection or it will trap air and not go back together. Before you take the two halves apart, make sure there are clear alignment marks. Consider verifying the Driveshaft Phasing.

 

>Carefully inspect the driveshaft yokes for signs of looseness, fatigue or cracking. Verify the pinch bolts are torqued and the the yoke collars do not slide on the output or input shafts.

 

>Inspect the shock eye connection to the swingarm. The early V11 white spring/blue collar Sachs-Böge are prone to crack.

>Service the cush drive. The button head screws will not likely come out willingly, so expect a fight (heat and penetrating oil/solvent) and replace with new fasteners.

>Clean and lubricate all the fasteners. I use a small wire brush and anti-seize paste.

 

>Inspect, clean and seal the main ground(earth) cable to the back of the gearbox. You have to remove the seat latch release to get to it. If you find the cable is not directly to the gearbox, move it there, but be careful if you remove the bolt entirely as there has been a report by SeanP61that it might not just go right back in.

 

> Remove, clean, lubricate, adjust, and shim (if necessary) the foot shift lever and mechanism. They get sloppy, loose, crudded-up, and misaligned. So much better with no play, sticking, or striking the frame side plate on the down stroke.
 

  • Like 2

Share this post


Link to post
Share on other sites

After 2 1/2 years and almost 3,000 views, I hope this posting has been helpful to viewers. I admit, I refer back to it to keep my Sport up to the mark!

 

I realize, though, that the thread is locked. So, please, if you have any suggestions, corrections, or additions please PM me on my profile.

 

"We few, we happy few, we band of brothers!" :mg:

  • Like 2

Share this post


Link to post
Share on other sites

Trying to follow my own advice, and add new things learned:

rear bearings and brake

Share this post


Link to post
Share on other sites

×
×
  • Create New...