Chuck 1,467 Posted August 24, 2016 Report Share Posted August 24, 2016 I have a little spare time, and am looking into this. The easiest way is just to weld an extension on the original.. I think that's what Phil did. If there's enough interest, I'll make a form tool and new levers out of 4130 with the 12mm extension on the CNC mill. How much would I have to charge? Dunno. I guess it depends on how many I make, but it Shirley wouldn't be over $50. Reply here or send an email to 59.Chuck Gmail.com 2016-08-24_03-08-08 by Charles Stottlemyer, on Flickr 1 Quote Link to post Share on other sites
Scud 1,298 Posted August 24, 2016 Report Share Posted August 24, 2016 2 for me, please. Quote Link to post Share on other sites
czakky 342 Posted August 24, 2016 Report Share Posted August 24, 2016 One here Quote Link to post Share on other sites
docc 3,554 Posted August 24, 2016 Report Share Posted August 24, 2016 A Chook-made LookyPhil Shift-binky? Moost have one! Quote Link to post Share on other sites
Lucky Phil 1,933 Posted August 24, 2016 Report Share Posted August 24, 2016 I have a little spare time, and am looking into this. The easiest way is just to weld an extension on the original.. I think that's what Phil did. If there's enough interest, I'll make a form tool and new levers out of 4130 with the 12mm extension on the CNC mill. How much would I have to charge? Dunno. I guess it depends on how many I make, but it Shirley wouldn't be over $50. Reply here or send an email to 59.Chuck Gmail.com 2016-08-24_03-08-08 by Charles Stottlemyer, on Flickr You're the man Chuck I'll take one for the cause. I looked at making a complete one as well but I'd have to do it by hand which I would have if it was a flat piece, so I just went the weld on option. I did do a validation trial with a bolted on piece just to test though. I'll have a "Gator red" one Chuck Ciao Quote Link to post Share on other sites
MartyNZ 424 Posted August 25, 2016 Report Share Posted August 25, 2016 I'm keen to buy one too. And if there is any other interest from NZ, I can act as your distributor if that suits you. Quote Link to post Share on other sites
Craig 53 Posted August 25, 2016 Report Share Posted August 25, 2016 I'll take one in titanium or carbon fiber. Seriously though, I will take one. Quote Link to post Share on other sites
Chuck 1,467 Posted August 25, 2016 Author Report Share Posted August 25, 2016 Ok, I'll make the form die today. Quote Link to post Share on other sites
Kostarika 94 Posted August 25, 2016 Report Share Posted August 25, 2016 Count me in for one. Quote Link to post Share on other sites
terje_m 6 Posted August 25, 2016 Report Share Posted August 25, 2016 One for me! Quote Link to post Share on other sites
footgoose 952 Posted August 26, 2016 Report Share Posted August 26, 2016 what's it extend? I've been outa town 1 Quote Link to post Share on other sites
Craig 53 Posted August 26, 2016 Report Share Posted August 26, 2016 what's it extend? I've been outa town See the thread on shifter improvements. 2 Quote Link to post Share on other sites
footgoose 952 Posted August 26, 2016 Report Share Posted August 26, 2016 what's it extend? I've been outa town See the thread on shifter improvements. Got it. I'll take one Chuck Quote Link to post Share on other sites
nobleswood 244 Posted August 27, 2016 Report Share Posted August 27, 2016 Put me down for one. Thanks Chuck Quote Link to post Share on other sites
Chuck 1,467 Posted August 27, 2016 Author Report Share Posted August 27, 2016 I'll finish the tooling this afternoon. With any luck at all, I'll have the first part.. but.. when you are forming sheet metal what the math says and what actually happens isn't always the same. If it isn't it will be back to square one on the machining fixture. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.