Jump to content

Leaderboard

Popular Content

Showing content with the highest reputation on 03/08/2023 in all areas

  1. From the album: 2Stroke-Racing

    the very important first day of the year ride out
    4 points
  2. Yes, the wires are yellow and I'd not lean on them too hard. When I did the cam gear set, I had it all off for a thorough inspection. Subsequently the voltage started varying so I verified the entire charging system; I found the connector for one of the yellow wires to have some corrosion, so remade everything. It charges better than it ever has, always between 14.4 and 14.8 at speed and goes over 13.0 by 1500rpm. It's just weak at idle. I do have an aftermarket fuel pump, perhaps it draws more than the stock pump did.
    3 points
  3. Moto Guzzi’s Liquid-Cooled V100 Mandello | Cycle World
    3 points
  4. Nice to see, will cross paths for sure, I'm # 844 this year. Expecting to pick up some stops this next weekend...should be great riding weather!
    3 points
  5. +1 . . . Many of you know what a champion I have been on the HIGH Current OMRON (and now the High Current CIT). I am currently on my 7th generation of relays. (Yep, I got to say "Current" and "currently" in the same post. ) Ironically, my only relay failures have been the High Current OMRON G8HE. I traced this to a faulty regulator combined with probable voltage spikes from a failing Yellow Wire connection from the stator.
    3 points
  6. I'd fully serviced my relay connections with DeOxit, tightened spades and installed genuine (?) Omron relays per much discussion. I was in Daytona this weekend (not preferred, but old friends in town) and after a half hour of stop-n-go traffic in hot sun, 88*, just as I approaching a parking lot I began losing power, eventually barely moving, then only idling, then sputtering to a stop. Fortunately I drifted into a parking spot. I immediately removed the rear seat and felt the relays (1100 sport has 4) 3 were hot, #2, fuel pump, was too hot. I restarted twice, both times with sputtering and dying. I installed one of the spare relays we all carry and it seemed all was right again. Obviously, the air, pavement, and engine temps were very high, with no air movement under the seat. Also, my bike only holds 12.4 volts at idle, so current through the relay was higher than at RPM. It's rare that I enter any sort of traffic, but I thought a simple enough solution is to mount a computer fan to blow across them. There's plenty of room outboard in the tailpiece, so I'll be doing some discovery on that pretty soon. I'll see if I can't engineer some test scenarios with heat gun and pictures.
    2 points
  7. Very much so docc. I love the style of the classic standard. So many iterations to choose from. When I'm tempted with something new, I look back at mine and wonder what's the point in chasing what I already have. Early concept pic, some things have changed. it has mufflers now
    2 points
  8. Are there indications to simply replace with an OEM regulator? Does the 1100 Sport have same vulnerable yellow output wires that are prone to breaking off at her stator?
    2 points
  9. I suspect your W650 is much like having a Honda GB500. Fun, interesting, reliable and my GB has kept me from buying lots (and lots) of other bikes . . .
    2 points
  10. the raised screen is the same screen.. but extended (duh) so they can be trimmed (I did) easily with a jigsaw and the edge smoothed out with sand paper. Re-cover the edge with oem or box-store edging. I actually made mine an inch lower than stock because like scud, I like the wind lower. ... and it looks cool
    2 points
  11. I'm kinda with the reviewer. No real preference. I prefer the RE motor concept 270* crank, I'll bet it sounds lovely and I love twins. I'm not in love with the look however, as much as I am the BSA. Don't care for the BSA radiator but it's an advancement I'm wiling to accept. The concept of smallish/retro/standard is the only point I can consider and address, and that puts the BSA in front for me... I like that they embraced their Arms heritage coming back to market. TBH my interest in bikes in that category is firmly in the vintage originals. If I were to cave and opt for reliability and newness I'd go for a used W650 or even a new W800. For now my 1980 XS650 is occupying that space nicely.
    2 points
  12. I don’t know how attractive a feature the down-sweep gauges is, I find it weird and confusing to look at. I guess you’d get used to it. Like someone famous here said not too long ago, as with music or women, it’s a good thing we don’t all have the same taste. As for the power these engines put out, although these bikes aren’t at all about absolute power output, the RE 650 twin is notoriously under-stressed and can easily be brought up to breathe a bit more with proven simple mods. And with its Harris Performance designed chassis the RE 650s have been reported as excellent handling machines. It’s common knowledge that Royal Enfield also has a history of firearms manufacturing in the UK, closely related to BSA in fact, but please spare me the guns logo on my motorcycle, I don’t want my fun and joyful passion to be associated with a death tool.
    2 points
  13. I received the shirt yesterday. I have not worn it on my motorbike yet. It looks like in the pamphlet above; a sweatshirt with protections. The fabric feels pretty tough. Is it going to be better than a jacket in the Texas hot and humid weather? I will let you know as I am going to start riding with it from today. By the way, if any of you were to purchase one, the midsection is particularly form fitting ; I guess I am going to have to cut down on French cuisine... I am a medium in the USA, I ordered Large European. The shoulders are spot on, but the abdomen requires a 16 years old body...
    2 points
  14. Posts specific to other V11 for sale have been split to the proper thread with respect to the OP . . . https://www.v11lemans.com/forums/topic/30488-v11-for-sale-online-craigslist-and-all-others/?do=findComment&comment=286605
    2 points
  15. It's interesting how when something sits for years it begins to show its age, even if it is sheltered. Paint and other finishes oxidize, as of course do metallic parts, and plastics can do weird things too as they age, especially if they were cheaply made. If one hasn't checked on it for a couple+ years, it is always amazing to find something like corrosion or peeling paint and wonder "how did that happen?". ...time happened For example, my bike has been sitting covered for many many years in a garage, and cleaned and started at least a few times a year, but the garage is not climate controlled. So condensation, humidity, dust, "air" have still taken a small toll on some of the finishes, and in a few cases a more serious toll. One example is the front subframe. The left side where it bolts to the engine has rusted significantly and the paint on the subframe around that bolt has peeled away. I can only assume this is where condensation from humidity settled for years and got under a knick in the paint. It's not a big deal, I actually have a spare NOS subframe, or can just have this one repainted, but is interesting to see how things can deteriorate even when sheltered.
    2 points
  16. This year, I am going to blog it differently; rather than piecemeal following post additions, I will update the first post (if possible; I remember there is a limit to the number of photos one post can contain) as I complete the tour stops. Everything will be in a single post, at the front of the thread. Easier to follow. Here's the map for 2023 50 stops( not formatted for phone view): this year, there are three additional "Alternative stops" that can be substituted for any of the 50 contractual ones. Once I have made a stop, I change the color from red to green. I should report distance and gas mileage. The purple colored stops are those which I will replace with alternates. 22/23/24-Sep-2023 update: Panhandle/Marfa loop (North and West) 1753 miles (2821 km) - about 27 hours of riding time; Ten stops; total 50 stops including 3 Alternates, out of 50 Highlights: -Longest ride so far, with a single day ride of 579 miles (932 km) via US-90. -The 5:00 AM Mclean to Seagraves trip down the US-70/256 through the Caprocks Canyons -The Kent to McDonald Observatory 118 road; better than the Twisted Sisters -The US-90 scenic route back from Marfa instead of the typical I-10 -The I-20 and its 80 mph posted speed, the highest legal speed in the USA! I did take the opportunity to remove the carbon deposits from the V11. -No more fuel injection issues; I do not have any explanation other than fixing the left cylinder boot that had come out of the admission pipe. If this was it, then was a leak since I got the bike. Lowlights: -Difficult to find air at gas stations. It used to be a staple of what you could expect and now missing or not working at almost every gas station I fueled. When I departed from Mclean at 5:00 AM, the temperature was below 70 degF. With such temperature variations in Texas, it is important to be able to check tire pressure. -Drivers not switching to low beams when crossing you; driving down to Seagraves from Mclean, it was still night and most of the vehicles I crossed did not bother switching to low beams. It is especially hard with trucks with several additional lights. No nice! -In Pecos, I lost idle briefly. I think it had to do with the extremely high temperature +100 degF, combined with multiple engine starts in a short span of time (I was relocating the bike). Apart from that, the Le Mans was perfect. -I thought the temperatures would be in the 80's, but no. Most of the trip was well into the 90's or better, excepted for the early Mclean start in the panhandle. -I wanted to take a picture of the Le Mans under the starry skies of Marfa, but it was raining that night... better luck next time. -The wind! from Midland to Kent, on the I-20 SW, I had a head wind which was making the fairing waddle left to right continuously. Remember the posted speed is 80 mph on the I-20. Rear view mirrors shaking with the fairing; useless! -Fuel consumption; I rode this trip as I did all the others before. Yet, I averaged considerably less mpg. I suppose this may be related to having an improved fuel injection, but I have no rationale for it. In Pecos, there was a ribbon of plastic flying that got caught on my left turn indicator, and overheating on my exhaust pipe. It melted on the pipe and left a black streak which is very hard to get rid off. Fuel Management: 51.838 US gallons total for the trip. I noticed that it is only 1309 miles according to my odometer. Its a considerable difference with the theoretical distance from the google itinerary of 1753 miles.... Another noticeable difference this time around, is my MPG. On the way to Shamrock (Route 66), my fuel efficiency was lower than expected by a lot! I do not have an explanation for it. Also, the 3000 rpm Fuel Injection issue has vanished since I fixed the boot on the left hand side of the admission pipe. The V11 works without any fuel problem. Strange. Riding Gear & Miscellaneous I thought the temperatures will be in the 80's and I was completely wrong. It was still very hot, especially coming down from Mclean once the sun started to rise, all the way to Marfa. Nevertheless, I only wore my Bowtex Elite Shirt, and the SIXS undergarment which I have well documented on this forum. As stated in the summary, I departed from Mclean at 5:00 am, and I would have liked to check my tire pressures, but could not. This used to be a staple of what gas stations proposed. I do not understand why it is not available everywhere. Only Costco seems to have it available. Stop #36 This was my first stop after 8 hours out... this is the old bank vault with the jail right behind it... I should have explored more, but I was trying to get some rest, and the sun was pounding me at 1:00 pm! Stop #22: The depot was built in 1909 and is a typical example of the Spanish Colonial Revival architecture. It was used as a passenger station and offices for the main line of the Quanah Acme and Pacific Railroad. Today it is a Museum full of memories from those days when railway was a main mean of transportation. Stop #7: This stop needs no introduction, since Route 66 is very well known; lots of tourists in the U Drop INN historical cafe, and a Tesla charging port right behind the complex. I bumped into foreigners following the Route 66, by car though... I would have waited for the night neon, but it was only 4 pm when I arrived, and the U Drop Inn closed at 5, so I would have had nowhere to wait. Elvis allegedly sat in a booth in this Inn, he was staying at an hotel nearby in between performances. Stop #5: The "Devil's Rope" Museum, a.k.a. barbed wire. For those of you interested in history, the barbed wire as we know it was patented by American Joseph Glidden in November 1874. It was an amelioration of the invention of the French Louis Janin in 1865 himself having taken the idea from another Frenchman, Léonce Eugène Grassin-Balédans in 1860. Barbed comes from the French "Barbel", hence the French name of barbed wire: barbelé. The great contribution from Joseph Glidden was a fast way to deploy it, using reels. The Museum contains all kind and variety of barbed wires, including those not so nice used during the first and second World Wars. Overnight at the Cactus Inn, Mclean TX A unassuming hotel, clean and owned by an elderly couple. I found that some families are living in this hotel on a permanent basis. Like the driver of that truck parked upfront. When you ride early in the morning, using the back roads, you are practically alone and able to absorb so much of the beauty surrounding you. I had a schedule to keep, unfortunately, but needless to say that I could have taken countless gorgeous photos. Texas is full of wind turbines! when it is dark, they have these red blinkers on, and if there is no visible moon, it looks eerie to see those lights above ground, but nothing else.... Stop #45, Hotel Texan Seagraves; I stayed there last year, but they had no vacancy this time around. For a good reason, when I arrived there, they were preparing for the annual town festival. Some of the people setting up nearby invited me to stay, and I wished i could have had. But the road to Marfa was still long. Stop # 24 Permian Basin Museum, Midland TX; What Texas is all about, or used to be all about maybe? oil and gas. I did not have time to visit the Museum, but I will one day. It contains a lot of the historical technology that started it all. Midland is a bustling city with a lot of jobs looking for willing people. Stop #12, Odessa TX; Fortunately, only a few miles away from Midland. I was told a lot of the oil and gas workers live in Odessa since Midland is now so expensive. Stop #14, West of the Pecos Museum, Pecos TX. I will not keep a good souvenir of Pecos. The town was a gigantic traffic jam, mostly due to 18 wheeler going in or out. This is also where a long plastic ribbon got caught on my left turn indicator, and melted on my exhaust pipe. It is very difficult to remove now. As mentioned in the recap at the beginning of this report, the 118 road from Kent to Fort Davis is a motorcycle rider's paradise. Twist and turns, up and downs. The catch is there aren't many vehicles on this road, and there isn't any connectivity either. Don't overdo it because there are plenty of places with sharp drops, and you are mostly on your own. Probably a good reason to never ride alone? you can see the McDonald Observatory further up, and the cloudy skies was a good indication that I would not catch any stars that night. Stop #28, McDonald Observatory TX; The ride to there was unbelievable fantastic, and more was awaiting from there to Fort Davies. I left that site at 4:30 pm, to head to my last stop of this 2023 tour: Marfa. Stop #34, Marfa lights viewing area, Marfa Texas. It is going to rain soon, I took the pictures for the tour, and decided to go to the hotel and come back at night. The sun was trying hard to go through the clouds at this moment. On the way back to Houston from Marfa, I chose to go through the US-90 instead of the I-10. The US-90 should be considered a scenic road as it is really crossing some beautiful landscape. Here's a photo of the bridge crossing the Pecos. That's all folks! 2023 Motorcycle Grand Tour of Texas is complete... 22/23-Jul-2023 update: Dallas/Abilene loop (North and West) 1050 miles (1690 km) - about 17 hours of riding time; Eleven stops; total 40 stops including 3 Alternates, out of 50 Highlights: I did it! I rode in the currently challenging extreme temperatures of Texas. Met many interesting characters along the way, a lot of kindness and courtesy extended by strangers. I mean people stopping to ask if I was ok. Definitively, there is still some good in this world. Lots of compliments directed at the Guzzi, even if people have difficulty to differentiate a BMW from a Guzzi. Not a single issue with the V11 even in 116 deg F (46.6 deg C) which is the maximum temperature recorded on the Formotion thermometer between Albany and Abilene. That being said, the engine missing at low revs was exacerbated. Lowlights: From early morning until about 09:30, temperatures were bearable. Afternoons temperatures made the ride strenuous at times. I will expend about weather conditions below. The Formotion Thermometer sheared from its support during the trip. This is the second time. I had installed it on a rubber boss for this trip, but that did not suffice to impede its loss. Unfortunately, because I am doing the stops marathon style, my timing does not always coincide with the business hours of the places. Fuel Management: As reported here, I had to refill the tank with 87 Octanes fuel since nothing else was available. This was the 200 miles / 48.0 mpg entry. I was outside Abilene and the reserve light came on. Although I could not feel any difference, I stopped at each successive gas station to mix higher octane fuel. This is why I have three entries with lower mileage in between refills. The 48.0 mpg/200 miles and 35.0 mpg/60 miles are most likely not accurate because I did not fully refill the tank with 87 Octanes, but I did for the successive refuel. Also, the "Alon" Gas stations mostly found in rural Texas only propose 90 Octanes premium. In any case, I am confident my Le Mans does about 45 mpg average on highways, and 35 average in the city. Riding Gear & Miscellaneous I did the trip using the Bowtex Elite Shirt, and the SIXS shirts and padded shorts. In these extreme temperatures complicated by humidity, nothing is going to spare you the heat. The Bowtex offers some minimal protection against abrasion and hard falls, and SIXS gear is really the best I have found for this kind of weather. The Shirts are lighter than sports shirts, and the padded boxer shorts really help to alleviate the backside pain on long rides. Prior to my trip I ordered and received a top cover for the Guzzi, from "More Shade" at ETSY's marketplace. I am glad I did, because not everywhere was I able to park my bike in the shade. Not so much to avoid having a "hot seat" but rather to spare the tank from the UVs. I wore the Quies Earplug designed for Motorcyclist; they are more comfortable than the Alpine. The rings are smaller which combines with larger extraction tab, make them easier to extract. Unfortunately, with this kind of temperatures, it was unbearable to have ear plugs. I took them off at the first gas stop. More testing is required. Hearing Aids and Riding Care to Share your experience? HEAT! It was really hot! The first few hours from 05:00 until 9:30 were fine. Especially outside of Houston on the I-45 to Dallas. From 09:30 onward, riding became unpleasant at times. Opening your visor would equate to opening an oven door and getting a whiff of potentially burning air. The Formotion temperature were taken during stops, and with the gauge in the shade. During my ride from Albany to Abilene, on the highway, the thermometer read 115 degF, with the thermometer protected from the wind and direct sunlight. Suffocating! I also noted that while traveling you could feel temperature differences; probably due to changes in humidity. For those of us who have been in a sauna, it is the same feeling as when you pour water on the stones. The temperature is the same, but the heat index quickly increases. I did not carry any water, and did not drink between gas stops. But that's me. I have worked in deserts before, and I think I am resilient to heat. In any case, there are numerous stops offering fresh water along the way. Now, I admit that if I had had a break down, I may have regretted to not carry water with me. I simply have no room. I have seen very few motorcyclists during this trip. The majority of them were in San Angelo, on a Sunday morning for church. No helmet, T-shirts only. I bumped into another Texas Grand Tourer at the Vintage Cars Museum in Weatherford. It was his last stop, and he told me he had done the rest in May. Stop# 6 Moto Liberty Addison (near Dallas): They are a tour sponsor, returning each year. Stop# 37 Rider's Biker Supply Lewisville (Near Dallas) Sponsor, returning each year. Stop#15 Decatur: I did not understand the meaning of that mural. Stop# A3 Jacksboro (this is an alternate stop): This is the chamber of commerce of Jacksboro; unfortunately closed. This was the third alternate stop. Stop# 30 Vintage Cars Museum Weatherford: The museum was open when I got there. I looked at these cars with nostalgia, trying to imagine how it was to navigate the cities with them. I actually had the opportunity to ride in a Cadillac DeVille in the 80's, while in New-York. This was an incredible challenge to park. There's also that Suzuki 250, which seems to be at the wrong place. But it looked pretty nice! Stop# 9 Mobley Hotel (1st ever Hilton Hotel) Cisco Conrad Hilton was in Cisco to purchase a bank. Instead, he purchased this hôtel which was making good revenue by renting the same rooms to multiple individuals. This was called "hot bedding". There were some oil workers, working 8 hour shifts, and not enough hotel rooms. The lack of Hotel rooms got Hilton interested. The rest of the story is that we now have Hilton hotels all over the world. The hotel was restored by the Hilton group recently, and you can visit it. But I could not since I arrived before visits started. Stop# 44 Sinclair Gas Station Albany There are plenty of these former gas stations, restored by the cities. Memorial to the older days. Stop# 39 Fort Phantom Hill near Abilene Interesting story, but I did not find any rattle snakes. Probably too hot even for them! Stop# 48 Harbord Kourt Hotel Coleman Coleman was my overnight stop for this trip. I could not get one of the 5 rooms they typically rent unfortunately. Sold out; third year in a row. I had dinner at a local Texas dinner, and was the only one without a cowboy hat... I felt odd. I am still finishing my digestion since the amount of food they give you could probably nourish an entire school for several days! and all that for a few dollars less, not more! Stop# 31 Railway Museum San Angelo I got in San Angelo around 09:30, and the city was bustling with people going to church, including a lot of Harley Riders with their better halves in tow. Again, the museum was opening at 13:00, so I had to continue to my next stop. Stop# 26 Mural in Eden This was my last stop for that trip. The return to Houston was just as hot as the rest That's all for this trip! see you on the next one... 26-May-2023 update: Frio Canyon loop (South West) 620 miles (998km)-10hours 25 minutes ride Five stops; total 29 stops out of 50 Highlights: Did the FM 337 (one of the three twisted sisters) from Medina to Leakey, coming from Bandera's Flying L Ranch. Last year, in 2022, at the same stop the V11 would not start again, forcing me to abort and go back home. At the Texas Motorcycle Museum, I could see a Moto Guzzi Daytona RS up close and personal for the first time!!! the bike is stunning! Lowlights: I installed a bracket to hold a camera so I could record the 337 run on video. Unfortunately, this is a camera equipped with gimbals, and the actuating motors are not strong enough to withstand the wind. I did some trials before the trip, with the camera perfectly behind the screen. But I changed the placement and found out the hard way that if exposed to the wind, the gimbals lock and the camera stops recording. I realized my mistake, and made a second attempt, keeping the bike beneath 40 mph. I will check the footage and post it if interesting. At the Frio Canyon Motorcycle stop, as I was backing up the Le Mans to park, my foot slipped on gravel; I nearly dropped it. Fuel details for the trip: I started on May 26th at 06:00; tank top off on May 31st after running errands. Something to take into consideration: the more refuels with less mileage in between, the greater the possible error. The three main refuels during the trip are all around 47 mpg and almost exclusively without any traffic. In the city, the mileage is around 40 mpg. Stop #32, Alamo BMW in San Antonio Stop #10, Flying L Ranch in Bandera Stop #23, Frio Canyon Motorcycle Stop near Leakey. See the gravel on the ground? hazard when backing up the bike on the incline.... Stop #21, C-47 Aircraft, Gillespie county airport near Fredericksburg Stop #29, The Texas Motorcycle Museum, Johnston City 01-May-2023 update: North East Texas 644 miles (1036km)-10hours 36 minutes ride six stops; total 24 stops out of 50 Highlights: In Corsicana, a driver stopped to talk to me while I was taking the Clint Eastwood Mural picture. He saw the bike, and told me he had a V7 Sport Guzzi when they came out in the 70's. In Gladewater, a young rider and his girlfriend came to chat about the Moto Guzzi brand which there weren't aware existed. In Jefferson, met a retired Policeman who did active duty on Moto Guzzi 750 and later 1000. he shared some photos of him while on duty riding those bikes. He was quite emotional telling me that since he retired, this was the first time he saw a Guzzi. Lowlights: Because of road flooding, I could not take the quickest itinerary between Jefferson, my last stop, and Houston. I had to take the 59 to Center, then the 96 to Jasper, the 190 to Jefferson, and resume my planned road. From 619 miles it became 644. This Eastern part of Texas has lots of forests, single lane roads, lots of lakes, nice to ride however.... On the 190, a truck towing a boat on a trailer turned left in front of me. I do not know if he saw me, but I had to brake in emergency to avoid hitting the trailer. The speed limit is 75 mph on these roads, and the guy turned left all of a sudden. No turn indicator. This was a close call. If I had not been pressed by time, I would have chased him to make him aware that he had cut in front of me. Fuel Details for this trip; Notice the differences in gas prices with Houston and the rest of the towns I visited... my fuel mileage is pretty good on the Le Mans. One detail, I tuck myself behind the windscreen on highway rides. It probably helps a lot. Stop#11 Clint Eastwood Mural in Corsicana Stop#1 Transformer Statue in Terrel Stop#17 Derrick in Gladewater Stop#18 Gladewater Museum Gladewater Stop#16 Old Fire Truck Gladewater Stop#46 Jay Gould Railroad Car Jefferson Trip done on Monday 24th, April 2023; page updated on Thursday 27th, April 2023. Count: 18/50 Texas Side Cars loop; 5 stops; 1 alternate. Itinerary: 539 miles (based on Google Maps; Total riding time 09:00 hours (estimated). Fuel details for this trip: Stop #4: Donnie. Stop #49: Old Fort Parker Grœsbeck. Stop #19: Gulf Gas Station Waco. Stop #42 Humble Gas Station Lampasas. Stop #40 Hill Country Motorhead Museum Burnet. Stop ALT-2 Henrietta the Hippo Hutto. Trip done on Monday 20th, March 2023; page updated on Tuesday 21st, March 2023. Gulf Loop: around 400 miles total. 40 to 50 degrees F: Fuel details for this trip: Stop #33 former Kingsbury post-office: Stop 38 Chisholm Trail Heritage Museum: Stop #20 Edna Movie Theater: Stop 43 Hotel Blessing: I was warned beforehand! one of the best buffet for homemade real food... they only accept cash unfortunately. Stop #ALT1 Pete the Mule (in lieu of Stop #50 Lonestar Rider who is doing a 48 States ride): Stop #02 Buddy Holly Center: Stop #03 12th Armored Division Memorial Museum: Stop #41 Historic Comanche Depot: Stop #8 History of Coryell County Mural: INITIAL Mileage before starting the 2023 tour; Stop #27: Navasota Classic Rock Coffee Co. & Kitchen: Lady #683: I did the same mistake parking with the front end first here. This is an incline and with a heavy bike, you cannot get out anymore. Fortunately, the car parked on her left hand side moved. Stop #25: Houston Red Roof Hotel: Red Roof is a sponsor of the tour; Stop #47 Galveston Naval Museum: Approximate calculated mileage Stops 27, 25, 47: 281.3
    1 point
  17. Excellent condition Rosso Corse. About 9,000 miles, 2nd owner. Many extras installed, including H&B Bags with rack, Russel Day-Long saddle, Bar Risers, Roper Plate, running lights. Bike had upgraded performance package and titanium exhaust. Located in northern Wisconsin. Send a message for more info and photos.
    1 point
  18. This is supposed to be stand-alone. It has all the protections included. This is a brand new item for Bowtex, and after my order, they informed they were manufacturing the first batch. I intend to wear it directly on one of the SIXS undergarment that I purchased last year from Italy. Those are really lights. I will give Bowtex feed-back, however I don't think this is going to be the solution for the Texas weather. True re the bandana requirement. Although my helmet may help, I will verify everything after my first test drive.
    1 point
  19. They are spectacular to own and ride, PS. Thx Doc for the heads up on mine.
    1 point
  20. just to add... my "intermittent" issues occurred when bike was hot, resolved when cooled off some.
    1 point
  21. Many Thanks Doc. I've just used your info to source a kit from Australia from Gowanloch
    1 point
  22. In my experience (nearly 40 years as a sound technician), any electrical circuit, and anything electronic, can have intermittent problems.
    1 point
  23. Looks like a compression Jiu-Jitsu snug fit. With the Texas sun, you'll get to wear a few bandanas to avoid sunburn on the neck...are you planning to wear this under the vented jacket or as a stand alone type item?
    1 point
  24. No engine heat problem, to far away. Smells more like a Shindengen fix . Cheers Tom.
    1 point
  25. 1 point
  26. I just found another one: https://www.road-race-service.de/product-437.html I know absolutely nothing about that vendor. Just stumbled across the site whilst looking for a screen for my V35 Imola. Hens teeth are easier....
    1 point
  27. TPS setting, etc. is similar to the V11s. These Instructions are very helpful: http://bradthebikeboy.blogspot.com/2012/10/throttle-position-sensor-setting_21.html I have used Guzzidag for this too. Unfortunately the Vintage is running very lean. The Cali is popping and stuttering as soon as the ambient temperatures are high e.g. 28- 30°C. I have tested various maps (one from Beetle - very rich and also useable for gasoline of bad quality I guess). I also worked together with Beard (Guzzidiag) and got one which is better than stock (but also lean) but this one did not work so well in another Vintage. All those maps switch off the lambda probe, so you have to set the CO-trim (possible with Guzzidiag). I ended up with a fine tuned mapping from DÄS Mototec (Germany) on a 15M ECU which solves all the problems (lean running, torque dip). This mapping was made for an airbox w/o snorkels and a BMC air filter but I have decided to keep the snorkles otherwise it is much too loud for the driver. The bike still delivers more torque than stock . Däs proposed to lower the CO-trim then (e.g -20 to -30). I was lucky to get an used 15M ECU (from a Ducati) for approx 100 Euro, the mapping costs around 200 Euro. Roland Däs develops all his maps on a dyno test bench for individually for your motorcycle (which is more expensive I guess) but I have never visited his shop. I have just sent him the ECU which is good enough for me.
    1 point
  28. I'm not that familiar with ecu/efi or mechanics in general so I was reluctant to post, hoping that someone with more knowledge and insight might jump in; but I do own a CalVin and can give you some basics that may help you. The CalVin is basically a blend of 2 models, the chassis is like a California, but the engine ecu/efi is like a Breva 1100. You can apparently use guzzidiag on the CalVin in a similar fashion to the capabilities on the V11's; you don't get full access and control with it like you apparently do on a CARC bike. A factory defect that "all CalVins" ? shared, was the disintegrating fuel lines/pump assembly in the tank, one of the symptoms could be running out of gas at higher throttle levels as the fuel pressure leaks out inside the tank at higher levels, inform yourself and ensure that the fix has been done, lots of info on wildguzzi about it. Could the fuel line defect cause the pinging you are describing,,, possibly,,, I can get my CalVin to ping, if I'm a little lazy on my gearing, ie running the rpms too low, imho. They were known for lean mapping and running a bit hot, the 3rd muffler in the crossover is a bit of plug in the whole works, I'm in the process of replacing mine with an H pipe, fwiw. Dead batteries on CalVins, are usually caused by using the 55 watt driving lights, most guys swap them out for lower wattage or LED bulbs, I just make sure that I don't turn them on, I have no idea if their use could have contributed to your blown 30 amp fuse, idk. The ECU "should" be a 15RC, TPS measurements have to be taken with a voltmeter at the TPS connection, I used little copper wire jumper cables, but picked up a Caspers break out cable for future use. I think the proper TPS baseline and idle settings can be a somewhat fluid thing, but at this point it seems that a baseline setting of 150-157 mv and an idle setting of 485-500 mv should be in the right ball bark. Iirc. The consensus on the best tuneup guide seems to be this one http://www.bikeboy.org/tpssetting.html Beetle does have a map for the CalVin, and his improved tutorial on guzzidiag over on wildguzzi is the go to reference for any of this type of work, jmho. Like any tuneup on a guzzi, I like to start it with the valves adjusted and finish with the TB's or carbs sync'd. Good luck Kelly
    1 point
  29. Next video: Moto Guzzi California 1100 (e.g. Vintage) – Checking and Adjusting Valve Clearance
    1 point
  30. Here is the next one ... about two screws
    1 point
  31. New Slideshow Video - Extend the Inner Rear Fender of a Moto Guzzi California Vintage
    1 point
  32. New Slideshow Video - California 1100 Shift/Brake Levers Maintenance
    1 point
  33. Two new slideshow videos - Internal Fuel Pump Unit & Double Cardan Universal Joint Assembly
    1 point
  34. New video: Moto Guzzi California Vintage - Replacing the 2006 Windshield
    1 point
  35. New video: Moto Guzzi California Steering Damper:
    1 point
  36. I made a new video about replacing the hinges of the side panniers:
    1 point
  37. I have added a Vintage to the Griso. For me this is the perfect combination. Some years ago I would never have thought to drive a bike like this, but it really has a lot of charme. I didn´t like the "Softchopper" looks of the later Tonti Californias but the "Calvin" really hides this with the stripes on the tank and the bags. The one I bought is 12 years old and has just minor optic issues (the ones we know from almost all Guzzis). The wheels fit perfectly to this classic bike, I cannot stand the looks of the Cali EV wheels for tubeless tires. The motor is the one from Breva 1100 with less HP but a bit more torque. What it really needs is an ECU with different mapping. The original one is a bad as the stock ones we know from the later V11s mit catalytic converters. The real problem is that spare parts became extremely expensive meanwhile. Maybe this video ("Moto Guzzi California Vintage Fog Beam Reflector Replacement") helps other Calvin owner:
    1 point
×
×
  • Create New...