Jump to content

Pete Roper V11 slosh trays now available!


Pressureangle

Recommended Posts

My thought was to keep the design and material as affordable as possible. Magnesium would be very light, but maybe costly.

1/4 in cold rolled steel plate would be inexpensive, the left side  is simple only needing a small section milled down where it bolts to the pork chop ( to keep it from pivoting),

the right side also needs this milled section, plus a round bunt, welded,or brazed at the point where the brake lever attach bolt goes to beef this section up.

Steel is heavy,but these brackets are small enough that weight shouldn't be a big deal. To futher keep the cost down,they could be offered in the raw, since everyone has there own color preferences, let the buyer do the final painting/powder coating. My idea is to keep the cost within reason, so that more folks would be willing to try a different foot peg position with out breaking the bank. I don't see why two simple brackets need to cost $300.

Link to comment
Share on other sites

Right... I looked into what I thought would be a low buck upgrade and retro fit ml63 calipers on my 550. I found a set of four for super cheap. 
 

Then I go to the Mercedes online parts book to order the brackets and they are about $250 EACH. Needless to say I didn’t go for it. 
 

manufacturers love to gouge you on parts that are seldom bought. Brake caliper brackets are not a “service item” soooo you’ll pay up the wazoo. I suspect it’s the same formula with these...

Link to comment
Share on other sites

  • 4 months later...
On 8/6/2020 at 5:29 PM, Pressureangle said:

For what it's worth, I have about 20 plates left, and intend to keep them available forever. Pete Roper will always get license on any new production runs.
Vic suggested that there may be other desirable components looking for manufacture; if so, suggest them and we can discuss demand and costs.

 

Thanks, @Pressureangle for making these Proper P.Roper Plates available!

New member @wdietz186 is looking for one to make sure the V11 he is putting back together does not "come from together" in the future . . . 

 

  • Like 1
Link to comment
Share on other sites

On 9/28/2019 at 9:52 AM, Pressureangle said:

Most of you probably follow the Redux thread, but I wanted to move the pertinent info to the top where it's not buried 7 pages deep.

Pete Roper licensed sloppage trays for V11 broad-sump motors, US-made in 304 Stainless Steel .080" thick. 
$70US, plus USPS medium priority mail box in the US, total $84.35.
International orders, $70US plus actual shipping. 

Please do send me a PM through the site, and I'll send an invoice. This avoids confusion and creates a solid timeline so nobody falls through the cracks.

PayPal to pressureangle@gmail.com
or check/money order to; 

Horst Manufacturing
9501 E. Center St.
Windham, OH 44288

;)

Bump!

  • Thanks 1
Link to comment
Share on other sites

  • 5 weeks later...

I’ll take one. Good timing, as I’ll be fixing one of the stripped sump bolts if the sun and warmth ever returns to NE Ohio. Just sent you the PayPal.

Not to hijack the thread, is there any easy way to check the other sump holes to see if they are near stripping? Besides over torquing them, of course.

 Thanks 

Bob Maynard 

  • Like 1
Link to comment
Share on other sites

Edit; disregard. I left half of them in Ohio. I still have plenty. 


21 January 2020. I have 2 plates left. 

I'll be ordering another 50 shortly- if it takes 2 more years to sell them, that's ok.

E.

  • Thanks 2
Link to comment
Share on other sites

Hi, 

I have a Roper new plate to install.

I recall seeing details / steps on V11lemans site.  on the install. Can't find it?  

Any help on finding it is appreciated.  

....... Thanks 

 

 

Link to comment
Share on other sites

1 hour ago, Coppa53 said:

Hi, 

I have a Roper new plate to install.

I recall seeing details / steps on V11lemans site.  on the install. Can't find it?  

Any help on finding it is appreciated.  

....... Thanks 

 

 

 

  • Like 3
  • Thanks 2
Link to comment
Share on other sites

Nice video. A good thing to do once you have the plate installed is to drop the dipstick in the hole and mark it level with the bottom face of the Roper plate, remove and drill a 1.5mm hole in the dipstick as your new "full" mark.

Ciao 

  • Like 4
Link to comment
Share on other sites

1 hour ago, Lucky Phil said:

Nice video. A good thing to do once you have the plate installed is to drop the dipstick in the hole and mark it level with the bottom face of the Roper plate, remove and drill a 1.5mm hole in the dipstick as your new "full" mark.

Ciao 

Sorry for my brain fade but..

Do you mean mark "it"  (the stick ?)  when its all the way in and with the oil level with the bottom of the plate or mark the stick when the end of it is level  with the bottom of the roper plate?  :doh:

Link to comment
Share on other sites

1 minute ago, KINDOY2 said:

Sorry for my brain fade but..

Do you mean mark "it"  (the stick ?)  when its all the way in and with the oil level with the bottom of the plate or mark the stick when the end of it is level  with the bottom of the roper plate?  :doh:

Sorry, with the plate installed and before you fit the sump insert the dipstick and mark it level with the plate lower surface then remove the stick and drill a hole. This way you know exactly when the oil level is at the bottom of the plate which is full.

Ciao

  • Like 1
  • Thanks 1
Link to comment
Share on other sites

7 minutes ago, Lucky Phil said:

Sorry, with the plate installed and before you fit the sump insert the dipstick and mark it level with the plate lower surface then remove the stick and drill a hole. This way you know exactly when the oil level is at the bottom of the plate which is full.

Ciao

Great!..Now I understand..Thanks Phil ! :bier:

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...