Lucky Phil
-
Posts
4,541 -
Joined
-
Last visited
-
Days Won
234
Content Type
Profiles
Forums
Events
Gallery
Community Map
Posts posted by Lucky Phil
-
-
I had the front wheel out a few days ago and the new wheel with the 25mm hollow axle and new tyre and disks is 2.2 KG lighter than the old front wheel, axle, disks and a partially worn tyre. So both wheels, the Titanium rear axle and the 25mm hollow front axle and bevel shroud removal saves 8.2 KG total. Not bad. I should have weighed the later clip ons as they are sure to be a bit lighter then the swan neck versions. I must weigh the bike and see whats the total weight. The 4 valve engine will weigh a fair bit more of course but the cross over and mufflers will be a lot less.
Phil
-
1
-
1
-
-
4 hours ago, gstallons said:
R & R the throttle plates is a critical process . You have to scribe their position with a pic or awl to make sure they are back in place PERFECTLY . I see no benefit in removing the throttle plate .
P.S. it is a free country , if you are attempting this the first time , I do not recommend it .
You don't really need to do this. You must keep the pates in the correct body and orientation upstream to downstream but when you install them you simply shut the throttle shaft hard with the plate loose and tap it a little to set the plate perfectly in the bore then tighten the screws. You need to clean up the screw threads and remove the staking and apply Loctite. I use blue and also mark the heads so I can check them from time to time.
Phil
-
2
-
1
-
-
3 minutes ago, stewgnu said:
70% Cleaning and 30% Curiosity.
I had loads of parts removed to identify an oil leak from the top of the engine, started cleaning everything, checking the loom etc etc.
It didn’t look like the po had ever cleaned the throttle bodies so they were pretty dirty. Taking the plates out allowed me to really clean them and the ports properly.
Now you'll have an issue with damaged threads in the throttle shafts.
Phil
-
1 hour ago, stewgnu said:
Ah right, well i’m setting valves, cleaning the butterflys + ports and balancing etc - i hadn’t thought to look at the injectors but i will do. Ta
Those torx holding the butterfly plates in are very soft aren’t theyWhy are you messing with them? I've had a few out for throttle body re bushing and new seals and they are staked in. You need to grind the tail of the screw to remove them. Never any need to touch them otherwise.
-
1 hour ago, audiomick said:
No. In fact, he doesn't seem to be offering any wheels at all anymore..
Well mine are beautiful wheels but the front wheel didn't fit the bike when delivered. The rear drive assembly was a very nice piece but the rear disk brake carrier had .2mm of runout! I removed it and machined it true. The front wheel wouldn't fit as the brake calliper bodies dragged on the disks because the captive spacer was 2mm too long. I had to press that out and machine it down and then it fitted. I emailed Roland about it with images of the measurements and dial indicator readings but he just told me to send them back to PVM. Not that useful to me so I fixed them myself. I think there has been changes at PVM and maybe they aren't interested in bespoke work anymore. Don't know for sure.
Add that to the many issues I've had as a foreign customer with different German suppliers over the last 2 year or so and I'm not keen to buy from them anymore. Don't know whats happened there but they are now far worse than the Italians ever were. Strange that and directly opposite to my old and pretty comprehensive dealing with them around 30 years ago.
Phil
-
4
-
-
1 hour ago, audiomick said:
I happen to know that they are PVM wheels, and Phil got them from Däs Mototech. However, even knowing that, I can't find them on the net. I rather suspect that Phil might have got (one of) the last set(s) that Däs had on offer.
I'm not 100% sure, but I think they are from this series (but the V11 is not listed there...):
Yes they were a special order. Roland doesn't seem to be listing them anymore which doesn't surprise me.
Phil
-
2
-
-
2 hours ago, audiomick said:
So the moral of the story seems to be, read everything here and everywhere else you can find good info, believe it all, and then have a look for yourself and think very carefully about it all despite what you have read up til then.
Pretty much. I did a how to post years ago. It's all pretty straight forward. High points
Don't attempt to adjust the main eccentric adjuster on the bike. It's a bench adjustment only despite what people do.
The shift returns spring on the stop plate assy can be installed upside down. When installed wrongly the spring arm rubs on the cover
The pawl arm over travel stop if adjustable should be .60mm clearance at the minimum point in the travel
Fit a scudd needle roller to the detent drum
Fit a Chuck spring
Check the pawl arm is straight and fine finish the contact faces.
Phil
-
3
-
-
2 hours ago, audiomick said:
Thanks Marty.
Then the workshop book seems to be misleading or incomplete(or I didn't read it thoroughly enough). Who would have thought...
I've done a few of these and my recollection is the dots line up in neutral and not all cam wheels have dots either. There are variations. Early selectors without the banana support and non adjustable overtravel pin and the later adjustable pin and banana support plate and as well as that there was an update kit sold for the earlier gearboxes that included a new cover, adjustable pin and banana plate.
Phil
-
2
-
-
I guess the front guard on the V11 is a "signature" piece as well and it kind of disappears when it's left in the natural carbon black. Now I have to cough up for a painting the front guard. It never ends.
Btw I had a strange front brake calliper issue. The callipers were bought second hand a while back and were in nice condition and came without pads. When I fitted and bled them the inner lower piston on the r/h calliper was leaking. Not a huge leak but a drip every day or so. Pressurised was slightly less so mainly a static leak. Anyway I pulled the piston and seals out and in the main seal oring groove was a foreign body maybe 1mm thick. No idea what it was but it was stuck in there very well, like a small blob of glue. Appears to have been there before the anodising and I managed to scrape it out carefully. There's no damage to the groove but you can see a small area where the anodising hasn't taken hence my theory of it being there pre anodising. I thought at first it was corrosion but it's not on the lower part of the groove where water would accumulate and the rest of the calliper bore is perfect. I could put it all back together but the seal outer face has been deformed slightly from sitting on the foreign body. BTW these callipers are hard to find now as they have been out of production for quite a few years and so are genuine rebuild kits.
There's a fairly new phenomena out there these days in that businesses are advertising stock on their websites but they don't carry any stock at all. They happily take full payment for stock they dont have and charge your CC then a week later inform you they can't get the stock anymore and refund your money. Then you lose on the transaction fees and they have your money for a week or so. This is very common now so for older bike parts it's advisable to email them first and see if they actually have stock or so they can at least check their supplier because they don't update their websites when parts become unavailable. It's bordering on a scam these days and I've been caught a few times of late. Some of the most professional looking motorcycle parts websites are in fact just resellers with no stock at all.
Phil
-
2
-
-
1 hour ago, audiomick said:
I think the green probably is better.
Your idea for the carbon guard with a clear strip in the middle might be a good one, if you can get it painted the right colour.
Thats not really a problem.
Phil
-
1
-
-
Fitted the original front guard. Better?
Phil
-
3
-
-
3 hours ago, audiomick said:
Could you tell me (us) which part number you are referring to? The parts must be on this diagram:
I expect to be going in there in the foreseeable future (maybe this winter), and would like to have those sort of things ready to go before I start.
PS:
How does one do that?
Item 13 Mick. I'd buy 2 but unless you're a ham fisted moron then snap rings/Circlips like these can be reused many times.
Phil
-
1
-
-
On 9/10/2023 at 9:18 PM, Steve S said:
I’ve got a new sender Craig
I might be interested in that if Craig doesn't want it.
Phil
-
12 hours ago, MartyNZ said:
I always make sure that I turn the engine forwards before valve adjustment too.
We know the thrust washer on the forward end of the camshaft can wear on the fwd face, so the shaft is loaded aft when running. I assume this is because the cam lobes run off-center of the cam followers to rotate the followers.
Turning the engine backwards may let the camshaft move forward and change the valve clearance.
Also the oil pump will deprime itself so oil pressure will be slower to rise on the next start.
The cam retaining fitting wears because of lack of lubrication not thrust. Guzzi use tapered cam lobes and domed lifter faces to achieve rotation and the lobes are tapered 8' of a degree in opposite directions between the lobes to avoid end thrust. The later retainers used oil slots to reduce wear on the thrust face. Rotating the engine by hand with a ratchet or spanner speed won't de prime the oil pump, same as it won't prime the oil pump at that speed turned in the correct rotation. It's simply too slow to do any pumping either way.
Phil
-
1
-
1
-
-
2 hours ago, pete roper said:
Yea thats them Pete. I'm a member of that mob but every time I try buying something it gets rejected. Not sure why. On the early bikes with the stick sensor you need to remove the ground wire and somehow uncrimp the holder and connect the wires internally and avoid the possibility of shorting out. Then you need to get the thing to seal fuel again around the nut and tank fitting. I suspect the plastic holder gets old and even with a new seal it wouldn't hold fuel and seeped after about 2 hours.
Phil
-
6 hours ago, Yam350 said:
My fuel level sensor is broken and it looks like the oem part is unavailable……has anyone found an alternative that works? I don’t mind having to replace the electrical connection to the bike.
What model is your bike? the external pump types are a bit of an issue. No new units available and the old units tend to go High resistance when they get old. The thermistor is easily available but almost impossible to replace and the methodology for it retention is quite fiddley and more complex then it appears. Old units also have a habit of being impossible to get to reseal 100% once they have been removed. I have replace my sensor with a blanking plug until I get a chance to manufacture a new aluminium and HDPE probe holder. The thermistor is no issue to source but you also need fuel proof wiring and potting compound. I have a design and materials but need some spare time.
Here is one thermistor option although a rip off cost wise. Strangely even the Chinese ebay equivalents are really expensive as well although if you by them in bulk from a Chinese manufacturer they are literally a $1.20 each or something.
https://www.npdlink.com/product/sensor-low-fuel-level-warning-sensor-mounted-to/107413
Phil
-
1
-
-
42 minutes ago, ScottMc said:
I have had a Ballabio for about 3 years and love this bike. Once I got it to shift it has been perfect. Except when you put a passenger on it. With two up it fails completely. My passenger, about 130 pounds, has no control when I apply the brakes and her weight comes directly to me. Most of the time I like this but it does make riding a little harder.
Has anyone found a seat/foot peg set up that makes this livable?
Buy the factory luggage rack, it doubles as a hand hold and makes pillioning better although it's always shit it's just a little less shit.
Phil
-
4
-
-
18 hours ago, drossell7 said:
The tank does not include the cap or fuel pump/filter.
So the only way to deal with this is to have the tank bead blasted to remove the paint back to the plastic. Dry the tank out and a full repaint. So probably around 600 dollars US for all that.
Phil
-
20 hours ago, Chuck said:
Thanks, Phil. I just put them in the lathe and used a parting tool to cut through the crimp.
Keen
Phil
-
15 hours ago, GuzziMoto said:
No doubt people on here have been through this. Alas, I am not one of them. I will point out that the hub that is too long is likely treated / hardened and just machining 6mm off it seems like it just isn't that simple. But I could be wrong. That is just my gut reaction.
Just take it to a local machine shop and get the required amount surface ground off it. Will take about 30 min on the surface grinder and magnetic chuck.
Phil
-
1 hour ago, 80CX100 said:
I didn't see your post when I made mine.
You're probably right;I've been shocked reading on social media about some of the Europeans worried about their bike mods passing the annual vehicle inspection.
Yea it's bureaucracy gone mad but they just have to suck it up so they hate foreigners mentioning it in reality. Can't blame them.
Phil
-
1
-
-
6 hours ago, 80CX100 said:
I'm sure it's well built and goes like a scalded cat.
Lately I can't even seem to manage to thread zip ties into place,let alone build something as beautiful as this,,,.
But now that you've brought it up,,, anyone going to this much time & effort and still leaves the hideous stock Griso exhaust installed,calls for a public flogging, jk.
As I said it's probably for European legality registration wise. The Europeans have some strict rego laws that are enforced.
Phil
-
2
-
-
Personally Chuck I would say the right hand plug in the image looks perfect. Clean ceramics, no speckly deposits, sharp defined edges on the clean electrode. The others look rich. Interesting plugs. You can remove the ceramics from the body then like old aero plugs?
Phil
-
It looks like V11 99-2000 frame or Daytona/Centauro frame fitted with a 1200 Griso/Sport engine and driveline and Daytona RS tank and fairing and Aprilia RSV1000R seat cowling. Interesting and fitted with the std Griso mufflers so one can assume it's been road legalised other wise why would you retain those massive things.
Phil
-
2
-
Triple clamp musings.
in Technical Topics
Posted
So here is the definitive answer to the triple clamp offset question. Twenty years in the pursuit. This is what you get when you use a later top clamp on an early lower clamp with fork tubes fitted. The stem doesn't line up with the stem bore due to the different lower clamp offset.
Another difference between the later and earlier lower clamps is the steering damper lug is 7mm longer on the later clamps so you need to machine that amount off the later clamps for the steering damper to fit correctly.