audiomick Posted May 7, 2023 Share Posted May 7, 2023 The Lonelec adapter works fine. On this computer, an oldish Fujitsu Laptop with Win10, the driver installed automatically. I didn't try the adapter with this computer, but am convinced it would work. I have another laptop, also oldish, a Dell Latitude with Win10 that I will be using in the garage. On that one, I had to install the adapter manually, following the instructions on the Lonelec web site. Otherwise, everything worked exactly as foreseen. 1 Link to comment Share on other sites More sharing options...
docc Posted May 7, 2023 Author Share Posted May 7, 2023 39 minutes ago, audiomick said: The Lonelec adapter works fine. On this computer, an oldish Fujitsu Laptop with Win10, the driver installed automatically. I didn't try the adapter with this computer, but am convinced it would work. I have another laptop, also oldish, a Dell Latitude with Win10 that I will be using in the garage. On that one, I had to install the adapter manually, following the instructions on the Lonelec web site. Otherwise, everything worked exactly as foreseen. So, this is an alternative to the 2-cable set we were previously sourcing from Lonelec? Link to comment Share on other sites More sharing options...
audiomick Posted May 7, 2023 Share Posted May 7, 2023 That seems to be the case. I assume that this is the two-adapter kit you are referring to: https://www.lonelec.com/product/guzzidiag-3pin-interface-cable-kit/ The first sentence in the description there is Quote We are now offering an alternative and even further improved 1 piece interface - please see here Whereby the "please see here" is a link to the one I got. 1 Link to comment Share on other sites More sharing options...
audiomick Posted May 14, 2023 Share Posted May 14, 2023 I sent one of the Lonelec KL-1TALIA adaptors mentioned above to Bernd, the Guzzidaig author, so he could have a look at it. The first thing he did was to open it up and have a look inside. His report was as follows: Quote A 'real' FTDI USB serial IC is used. There are "proper" capacitors installed. There is protection against accidental reversal of the polarity of the crocodile clips (bridge rectifier). A real KL driver IC is used and not some 'cheap' OP circuit. 2 small things to complain about: The inputs are not filtered (Ok, with 12V signal level and the driver IC behind it you can do that) The required USB cable is not included. I wondered about the USB cable myself. The ordering process involved ticking boxes regarding the type of USB connection, and I had the distinct impression there would be a cable provided. I didn't query that though, as I have USB cables lying around here that I can use. So, anyway, it looks like one can use the adaptor without any great worries. 1 Link to comment Share on other sites More sharing options...
Speedfrog Posted May 14, 2023 Share Posted May 14, 2023 Looks like you should have received 1 usb cable with the KL-1TALIA kit according to Lonelec description. Contents: 1 x KL-1TALIA Interface with 3 pin FAL plug. 1 x USB cable (A, Micro or C). 1 x DC power plug with battery clips 1 x Installation instructions. Link to comment Share on other sites More sharing options...
Speedfrog Posted May 14, 2023 Share Posted May 14, 2023 On 5/7/2023 at 11:46 AM, docc said: So, this is an alternative to the 2-cable set we were previously sourcing from Lonelec? This is at least the third iteration of Guzzidiag interface cables from Lonelec. This is what their original model looked like, somehow I ended up with 2 of those and they work just fine. Afaik there’s never been a problem connecting to Guzzidiag with cables sourced from them. 3 Link to comment Share on other sites More sharing options...
audiomick Posted May 14, 2023 Share Posted May 14, 2023 47 minutes ago, Speedfrog said: ...you should have received 1 usb cable with the KL-1TALIA kit according to Lonelec description. Yes, I saw that too. As I said, I'm not fussed about it not being included as I have enough of them already. However, I assume they would probably send me one if I complained about it. 28 minutes ago, Speedfrog said: This is at least the third iteration of Guzzidiag interface cables from Lonelec Afaik there’s never been a problem connecting to Guzzidiag with cables sourced from them. Two good reasons to buy there, I reckon. They're staying on the case, and they seem to have a good record. 1 Link to comment Share on other sites More sharing options...
mikev Posted May 30, 2023 Share Posted May 30, 2023 I just bought one of these too GUZZIDIAG JPDIAG DUCATIDIAG TUNEECU KIT - KL-1TALIA (3 Pin Connection) - USB-C Cable 1 Link to comment Share on other sites More sharing options...
docc Posted May 30, 2023 Author Share Posted May 30, 2023 1 hour ago, mikev said: I just bought one of these too GUZZIDIAG JPDIAG DUCATIDIAG TUNEECU KIT - KL-1TALIA (3 Pin Connection) - USB-C Cable With that, and a way to set your TPS mV, you will be golden. (After plugs and a valve adjustment.) Then, meticulously synchronize the throttle bodies . . . 2 Link to comment Share on other sites More sharing options...
mikev Posted June 6, 2023 Share Posted June 6, 2023 unboxing my guzzidiag cable from lonelec 1 Link to comment Share on other sites More sharing options...
mikev Posted June 6, 2023 Share Posted June 6, 2023 unfortunately on my mac, I get this error The application “GuzziDiag_V0.60” can’t be opened. so will have to scrounge a windows laptop Link to comment Share on other sites More sharing options...
docc Posted June 6, 2023 Author Share Posted June 6, 2023 3 hours ago, mikev said: unfortunately on my mac, I get this error The application “GuzziDiag_V0.60” can’t be opened. so will have to scrounge a windows laptop That could be a security/firewall setting in your OS. See if you can navigate to that section and list GuzziDiag as an exception. edit/ to wit: 1 1 Link to comment Share on other sites More sharing options...
mikev Posted June 10, 2023 Share Posted June 10, 2023 Using my son's windows computer I was able to get Guzzidiag to connect to my V11 this morning. CO trim was the number I most wanted to see and it was set to 0. Bike runs fine and idles fine so I didn't mess with any settings. The ECU top line had info but the bottom two lines were all 000's. Temp and RPM read well. RPM was about 100 less than what was displayed on the tach. Also, I didn't download any drivers. Only installed Guzzidiag_VO.60 3 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now