Jump to content
Jet

Ram Mount.

Recommended Posts

On 6/8/2020 at 5:51 AM, docc said:

Trying to clean up my act . . . :grin:

IMG_2583.jpg?v=1591572338946

I see the Forceps..Where's the Scalpel ...?? :-)

Share this post


Link to post
Share on other sites

I see the roach clip.. :rasta:

  • Like 2
  • Haha 1

Share this post


Link to post
Share on other sites
On 6/7/2020 at 6:50 PM, swooshdave said:

Life is so much easier when you know someone who has a lathe.

Any chance you have a drawing for the stem nut?

My guy couldn't find the "drawing" but sent me this..:-)   I couldn't find my drawing, but as I remember it, the outside diameter is 30mm, 1.180", I added 10mm to the length, the thread size is 23mm X 1.0mm, the through hole where the wrench flats are is 19mm, .750", and the wrench flats are 25mm across.

Share this post


Link to post
Share on other sites
On 6/9/2020 at 8:25 PM, KINDOY2 said:

My guy couldn't find the "drawing" but sent me this..:-)   I couldn't find my drawing, but as I remember it, the outside diameter is 30mm, 1.180", I added 10mm to the length, the thread size is 23mm X 1.0mm, the through hole where the wrench flats are is 19mm, .750", and the wrench flats are 25mm across.

yYtYr4g.png

How close did I get?

  • Like 1
  • Thanks 1

Share this post


Link to post
Share on other sites
10 hours ago, swooshdave said:

yYtYr4g.png

How close did I get?

i'll take one

Share this post


Link to post
Share on other sites
1 hour ago, footgoose said:

i'll take one

I may get some made, stay tuned. Need to verify the dimensions first.

Share this post


Link to post
Share on other sites
7 hours ago, swooshdave said:

I may get some made, stay tuned. Need to verify the dimensions first.

What are the thread dimensions of the stem?

Share this post


Link to post
Share on other sites
On 6/9/2020 at 8:25 PM, KINDOY2 said:

My guy couldn't find the "drawing" but sent me this..:-)   I couldn't find my drawing, but as I remember it, the outside diameter is 30mm, 1.180", I added 10mm to the length, the thread size is 23mm X 1.0mm, the through hole where the wrench flats are is 19mm, .750", and the wrench flats are 25mm across.

 

3 hours ago, docc said:

What are the thread dimensions of the stem?

You, who never misses anything. :ph34r:

Share this post


Link to post
Share on other sites
3 hours ago, swooshdave said:

 

You, who never misses anything. :ph34r:

Just concerned me that spanning the hex flats with a 25mm spanner, rather than KINDOY2's 30 mm, could make for some very thin walls . . .

Share this post


Link to post
Share on other sites
4 hours ago, docc said:

Just concerned me that spanning the hex flats with a 25mm spanner, rather than KINDOY2's 30 mm, could make for some very thin walls . . .

I don’t disagree which why I’m waiting for validation of the figures from @KINDOY2 who said the flats were 25mm and outside diameter was 30mm.

Share this post


Link to post
Share on other sites
1 hour ago, swooshdave said:

I don’t disagree which why I’m waiting for validation of the figures from @KINDOY2 who said the flats were 25mm and outside diameter was 30mm.

Maybe I'm interpreting this wrong, but wouldn't this mean 30mm across the flats?

" . . . enough space to machine to get  a 30 mm wrench on it to tighten. "

Share this post


Link to post
Share on other sites
Quote

and the wrench flats are 25mm across.

You can't have a 30mm diameter object and require a 30mm wrench. But you are correct that the first post did say a 30mm wrench. If I could get to my bike I'd measure the existing stem nut but there are a couple Nortons in the way. Damn British.

  • Haha 1

Share this post


Link to post
Share on other sites
On 6/12/2020 at 4:21 AM, docc said:

What are the thread dimensions of the stem?

Sorry I've been away nut is 23mm x 1.0 thread...same as stem...19mm on the inside

cheers

Share this post


Link to post
Share on other sites
On 6/12/2020 at 11:21 AM, docc said:

Just concerned me that spanning the hex flats with a 25mm spanner, rather than KINDOY2's 30 mm, could make for some very thin walls . . .

outside of the round part is 30mm..25mm  spanner..the thing doesn't require much torque  seemed fine  :-)

Share this post


Link to post
Share on other sites
On 6/11/2020 at 9:57 AM, swooshdave said:

yYtYr4g.png

How close did I get?

 

  • Thanks 1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...